01 z 08
Jak vyrobit Ultimate Wood Sawhorses
Zatímco viděli koně typicky něco, co byste si mysleli, že najdou na pracovišti, mohou být obzvláště užitečné v dílně. Dobrá sada křovin může být použita jako základna pro dočasnou stůl, držení přenosné stolní pily , ukládání řeziva ... seznam pokračuje dál a dál.
Tyto stojany jsou všestranné, velmi robustní a poměrně snadno se staví. Jakmile budete mít set, nikdy nebudete mít s sebou věci, které s nimi můžete dělat, dokonce i poté, co jste dokončili stavbu perfektní dílny.
Stupeň obtížnosti
- Woodw orking: Snadné
- Dokončení: Malování, je-li to žádoucí, ale není nutné
Doba dokončení
- 30 minut
Požadované nástroje
- Kotoučová pila nebo kotoučová pila
- Akumulátorová vrtací vrtačka nebo výkonová vrtačka
- Rozložení čtverce
- Svinovací metr
- Tužka
Potřebné materiály
- Devět (9) 2x4 dlouhých 8 stop
- 2-1 / 2 nebo 3 palce šrouby paluby
02 z 08
Vybudovat I-paprsky
Chcete-li začít budovat Ultimate Wood Sawhorses, začněte řezání 2x4 na dva kusy, jeden na 47-palců a druhý kus na 49-palců. Tento krok opakujte dvakrát, takže máte tři z každé velikosti.
Dále budeme shromáždit I-Beam, jak je uvedeno výše, začínajícími se třemi 49 palcovými deskami. Na koncích dvou desek označte středovou osu přes krátkou osu na obou koncích, jak ukazuje horní a dolní deska v diagramu. Když jsou tyto čtyři značky na svém místě, vyznačte středovou čáru dolů po dlouhé ose na každém konci třetí desky, jak to ukazuje schéma středové desky.
Nyní pomocí šroubu s připojte horní desku ke středové desce. Umístěte několik šroubů po celé délce horní desky a do středové desky, ujistěte se, že středové čáry jsou na obou koncích zarovnány. Když je horní deska připevněna k středovému panelu, otočte sestavu a připevněte spodní desku stejným způsobem. Po dokončení byste měli mít dlouhý I-Beam.
Opakujte celý proces s 47-palcovými deskami.
03 ze dne 08
Připojte nohy k I-nosníku
Pomocí nezkráceného materiálu vyřízněte 8 32-palcových nožiček. Možná budete mít možnost získat tři nohy z jedné 2x4, pokud je původní zásoba o něco delší než délka 8 stop.
Dočasně odložte 47palcovou sestavu a budeme pracovat s 49palcovou sestavou. Položte I-Beam na jeho stranu. Uchopte jednu z nohou a umístěte konec těsně pod okraj horní desky I-Beam.
Ujistěte se, že strana desky je zarovnaná s koncem I-nosníku, připojte nohu k I-Beamu pomocí dvou šroubů do středové desky a dvě do spodní desky I-nosníku, jak je znázorněno na obrázku výše.
Po dokončení jedné nohy opakujte s druhou nohou na stejné straně I-Beamu. Potom otočte celou sestavu a připevněte nohy na druhou stranu I-nosníku.
Když jsou všechny čtyři nohy připojeny, postavte sestavu na nohách a zkontrolujte, zda nedošlo ke kolísání. Nohy mohou být lehce rozloženy ručně, pokud je to nutné, aby byly všechny nohy rovnoměrně na podlaze.
Jakmile je 49-palcová sestava I-Beam dokončena, proveďte stejné kroky na 47-palcové I-Beam.
04 ze dne 08
Připojte boční struny k nohám Sawhorse
Jakmile obě jednotky stojí na svých čtyřech nohách, je čas stabilizovat nohy. Znovu začneme s 49palcovou sestavou.
Odřízněte dva 49-palcové kusy ze dvou 2x4. (Uložte mezní hodnoty, protože budou použity v dalším kroku.)
Pomocí kazety opatrně umístěte značku o 10 centimetrů po každé ze čtyř noh na vnější straně. Umístěte značku pomocí rozvržení .
Připojte jeden ze dvou řezaných kusů k oběma nohám na jedné straně sestavy, zarovnejte je právě na vrchol čtvercových značek a konce desek se vyrovnají stranami nohou, jak je znázorněno na obrázku výše. Opakujte na druhé straně. Dvě šrouby na každém spojení postačí.
05 z 08
Připojte koncové struny
V tomto kroku připojíme koncovku na každý konec pilového kotouče. To bude měřeno na místě.
Vezměte si kus 2x4 a uložte ho přes konce dvou postranních pásů, které jste v posledním kroku připevnili. Použijte tužku na desku tak, aby odpovídala vnějším stranám bočních desek, jak je znázorněno na obrázku.
Vyřízněte konce značkami, které jste napsali. Připojte koncovou desku k oběma nohám a koncům bočních desek, jak je znázorněno.
Opakujte na opačném konci a tato kosačka je dokončena.
06 z 08
Stavět druhý Sawhorse
Nyní, když je dokončena sestava 49-palcového píce, budeme soustředit pozornost na 47palcovou sestavu. Vzhledem k tomu, že 49palcová sestava bude hromaděna na 47palcové jednotce, budeme muset tuto konstrukci trochu jinak.
Všimněte si, na obrázku výše, že boční struny pro toto zařízení jsou na vnitřní straně nohou, na rozdíl od vnější strany na druhém pilníku. V opačném případě je tento krok stejný.
Proveďte značku 10 palců nahoru po každé ze čtyř nohou, tentokrát dovnitř. Umístěte značku pomocí rozvržení .
Ořízněte dvě hranice, která jste zadrželi od posledních bočních stran, na délku 47 palců. Připojte je tak, jak je to znázorněno na obrázku, dbát na to, aby zůstali na horní straně čáry tužky a konce desek se vyrovnají stranami nohou.
07 z 08
Připojte rozmetadla k druhému Sawhorse
Pro dokončení druhého pilového kotouče použijeme podobnou techniku jako na první pilu.
Všimněte si pozici koncových strun na obrázku výše. Umístěte kus 2x4 na horní část obou bočních nosníků, které překrývají nohy na koncích. Použijte nožičky k vyřezávání řezných značek na koncové struny.
Odřízněte obě desky k čarám a připevněte je k nohám pomocí dvou šroubů na každém upevňovacím bodu.
08 z 08
Stohování dokončených Sawhorses
Dřevo pro tyto pilčíky je nyní dokončeno. Můžete si je přát malovat , ale to je otázka volby.
Chcete-li skládat hotové stojany, 49palcová jednotka jednoduše sedí na horní straně jednotky 47 palců, jak je znázorněno na obrázku výše. Dvě stohované jednotky se snadno zapadají do rohu vašeho obchodu, dokud je nebudete potřebovat.